CHEMLEASE MOULD CLEANER
Mould cleaner. A unique solvent blend for removing buffing compounds, waxes, silicones and contaminants from moulds. It is wiped on liberally and then wiped off with clean, dry rags.
Available in 3.8 litre, 18.9 litre
SEALER 15 EZ
A high performance solvent based sealer designed to condition and seal mould surfaces. It reduces porosity moulds and acts as a base for new and reconditioned. Sealer 15 is a wipe on, wait 5 – 30 seconds, and wipe off system. 1 – 2 coats is recommended, 1 hour before applying release agents.
Available in 1 quart, 3.8 litre
CHEMLEASE ONE FS EZ
Chemlease One FS EZ is a semi-permanent release that is easy to apply and provides multiple releases for high gloss composite moulding. Used as a wipe on only product.
The EZ version of this material does not contain any chemicals listed on the Hazardous Air Pollutants list (HAPs). The original non-EZ formulation is still available for a limited time.
Available in 1 quart, 3.8 litre
75 EZ
A wipe on, wipe off solvent based semi-permanent release agent. Good under gelcoats and/or where high gloss is required. Good at helping to control pre-release. Wipe on and wait for evaporation 5 –30 seconds, 10 minutes between coats, 30 minutes before moulding. 4 – 5 coats recommended.
Available in 1 quart, 3.8 litre
41-90
Available in 1 quart, 3.8 litre
A wipe on only solvent based semi-permanent release agent. A high slip product for difficult moulds. Not good for gelcoats, as being so slippery the gels have trouble holding their films. Has a duller finish. 10 minutes between coats, 30 minutes before moulding. 3 – 5 coats recommended.
258R
A wipe on or sprayable water-based sacrificial release agent for difficult or abrasive moulds, such as in mandrel wrapping. 10 minutes between coats, 10 minutes before moulding. 2 – 3 coats recommended.
Available in 1 quart, 3.8 litre, 18.9 litre
TR 104 WAX
Is a high temp semi-permanent paste wax designed to handle all applications where a release wax would be used.
Available in 400 ml
PTFE FILM
Teflon mould release film with a self adhesive backing for a one operation mould release film requiring no release agent for multiple pulls.
Available by the square metre
Duratec Range, Mould and Plug Building
This novel range of polyester products from the U.S.A. is used to surface new moulds and tools, and to rejuvenate damaged surfaces. All the major composite builders now use it.
DURATEC POLYESTER SURFACING PRIMER, 707-002 GREY
Use Duratec Polyester Surfacing Primer to prime composite plugs and patterns, and a number of wood products – including those used for furniture, musical instruments and architectural applications.
Available in 1 gallon
DURATEC POLYESTER EZ SANDING PRIMER, 707-061 GREY
Duratec Polyester EZ Sanding Primer is an alternative to Duratec Polyester Surfacing Primer. The product offers faster curing time and easier sanding.
Available in 1 gallon
DURATEC POLYESTER SEALER, 823 CLEAR
A low viscosity, rapid curing, penetrating sealer that anchors lacquers, urethanes, polyesters, vinyl esters and most epoxies to a variety of substrates.
Available in 1 gallon
DURATEC SUNSHIELD CLEAR TOPCOAT, 904-061
A high-build, easily sandable coating designed as a topcoat for cured polyester, polyurethane and lacquer clear or colour coats.
Available in 1 gallon
DURATEC VINYL ESTER MOULD REPAIR PUTTY, 1802-007 BLACK
Duratec Vinyl Ester Mould Repair Putty is used to repair polyester and vinyl ester moulds.
Available in 1 quart
DURATEC VINYL ESTER HI-GLOSS TOPCOAT, 1904-045 CLEAR
Use Duratec Vinyl Ester Hi-Gloss Topcoat when a hi-gloss is desired after priming moulds.
Available in 1 gallon
DURATEC VINYL ESTER PRIMER, 1794-006 WHITE
Use Duratec Vinyl Ester Hi-Gloss Topcoat when a hi-gloss is desired after priming moulds.
